STOMA JSC

Artificial plastic teeth Estedent-02 are designed for application in prosthodontics for manufacturing of remov­able denture constructions. Plastic teeth Estedent-02 are manufactured on base of cross-linked acrylic polymers. They have a fluorescent effect (teeth put into partial denture look harmoniously near natured teeth in ultra-violet rays). Teeth Estedent-02 have a good chemical binding with denture base. Like their natural prototype teeth Estedent- 02 have optimal functional and cosmetic characteristics. Teeth Estedent-02 are manufactured in accordance with “Vita” scale and consist of 9 shades: A2; A3; A3.5; B2; B3; C2; C3; D2; D3. Due coloring scale Estedent-03 teeth comply with colors № 28, 32, 33, 34, 35, 36, 38, 40, 41.

Indications for use: manufacturing of complete upper- and lower jaw dentures; manufacturing of partial dentures; Strong points: high accuracy shape reproduction; high ultimate flexural strength; optimal elasticity; beneficial cosmetic effect due to denture translucency and introduction of «streaks» that imitate the soft tissues of the oral cavity; good polishing ability; Application instructions: mix powder with liquid in 2:1 ratio; plastic modeling phase is about 20 minutes; carry out the polymerization process in a water bath in dental flasks, by bringing the water bath to boiling point gradually within 40-50 minutes; polymerization process takes 30 minutes; do not retrieve the denture from the flask until it is cooled down completely;

Indications for use: manufacturing of temporary plate-type removable dentures; repair and restoration of removable dentures; maxillofacial appliances; orthodontic appliances; manufacturing of removable prosthetic splints; Strong points: multipurpose use; rapid guaranteed polymerization; beneficial cosmetic effect due to denture translucency and introduction in material of "streaks" that imitate soft tissues of oral cavity; good workability of products; Application instructions: mix-up powder and liquid in a 2:1 ratio; carry out the process of polymerization at room temperature in a heating cabinet at 35-45°C for 25-30 minutes; treat and polish the material by conventional methods;

modeling of removable denture bases; manufacture of occlusion templates with occlusive to ruses; manufacture of individual spoons and base spoons; Strong points: material has high plasticity properties; material is easy to mold; when tooled, the material does not break or delaminate; material is easy to remove completely from plaster molds using boiling water;

Indications for use: modeling of intermediate links of denture bridges and other fixed denture elements; Strong points: low degree of thermal shrinkage; ash content does not exceed 0,02%; material is easy to model using dentistry tools; dry and non-viscous chips are produced; Application instructions: soften wax slightly above torch flame; wax may be softened below an incandescent lamp or in water bath at 45-50 ºC within 3-5 minutes

Indications for use: application of coating onto curative liner (test filling) in carious cavities; material is used for temporary fillings; Strong points: proper adhesion to the tooth dentin; Application instructions: prior to introduce paste in a carious cavity, treat and dry up the cavity thoroughly; after taking some filling paste from the cup, close it tightly to avoid penetration of moisture therein;

Indications for use: fixation of partial and complete removable dentures; Benefits: provides a dense and reliable fit prosthesis to the gums throughout the day; has a calming effect on the painful areas of the mucosa; promotes better chewing food; Protects the gum from solid particles of food under the prosthesis; wearing a denture gives a sense of confidence, comfort; has no taste and smell, preserving the natural taste of food;

material is used as a soft-type lining in manufacture of removable denture designs; material is used in manufacture of maxillofacial appliances; Strong points: quick and easy manufacture of lining; no odor and taste; no toxicity; low water absorption; durable elasticity properties; stable connection between lining and denture base; compatibility with all standard removable denture plastics; Application instructions: treat the denture surface by removing 1 mm layer; clean and dry out the denture surface thoroughly; apply only 1 layer of primer; primer drying time is 20-30 seconds; total polyvinylsiloxane composition operation-use time is 1,0-1,5 minutes; polyvinylsiloxane composition curing time is 2,0-6,0 minutes; close tightly the primer-containing vial;